奧林巴斯OLYMPUS/D797測厚儀雙晶探頭

時間：2017-11-16閱讀：578

奧林巴斯D797測厚儀雙晶探頭|奧林巴斯OLYMPUS/D797測厚儀雙晶探頭

27MG測厚儀

45MG測厚儀

38DL PLUS測厚儀

MAGNA-MIKE 8600測厚儀

35RDC測厚儀

深圳華清儀器儀表有限公司優(yōu)惠價供應(yīng)奧林巴斯系列產(chǎn)品，具體想了解D797價格、D797貨期、D797實物圖、D797應(yīng)用等等，請來電與深圳華清儀器無損檢測部，謝謝

Gage Dual Transducers

Request a quote or purchase a transducer by selecting the item number.

Item Number	Part Code	Frequency (MHz)	Connector Type	Connector Location	Range in Steel (mm)	Range in Steel (in)	Temperature Range °F	Temperature Range °C	Tip Diameter (mm)	Tip Diameter (in)
U8450017	D797-?SM	2	Microdot	Straight	3.5 - 635	0.150 - 25	-5 - 752	-20 - 400	22.9	0.900
U8450016	D797	2	Potted	Right Angle	3.5 - 635	0.150 - 25	-5 - 752	-20 - 400	22.9	0.900
U8454038	D7910	5	Potted	Right Angle	1.00 - 500.00	0.040 - 20.000	32 -122	0 - 50	12.7	0.5
U8450021	D799	5	Potted	Right Angle	1.0 - 508	0.040 - 20	-5 - 300	-20 - 150	11	0.434
U8450007	D790-?RL	5	LEMO	Right Angle	1.0 - 508	0.040 - 20	-5 - 932	-20 - 500	11	0.434
U8450008	D790-?SL	5	LEMO	Straight	1.0 - 508	0.040 - 20	-5 - 932	-20 - 500	11	0.434
U8450009	D790-?SM	5	Microdot	Straight	1.0 - 508	0.040 - 20	-5 - 932	-20 - 500	11	0.434
U8450011	D791-?RM	5	Microdot	Right Angle	1.0 - 508	0.040 - 20	-5 - 752	-20 - 400	11	0.434
U8450002	D790	5	Potted	Straight	1.0 - 508	0.040 - 20	-5 - 932	-20 - 500	11	0.434
U8620225	MTD705	5	Lepra/Con	Right Angle	1.0 - 19	0.040 - 0.75	32 - 122	0 - 50	5.1	0.200
U8450010	D791	5	Potted	Right Angle	1.0 - 508	0.040 - 20	-5 - 932	-20 - 500	11	0.434
U8450014	D794	5	Potted	Straight	0.75 - 50	0.030 - 2	32 - 122	0 - 50	7.2	0.283
U8450018	D798	7.5	Potted	Right Angle	0.71 - 100	0.028 - 4	-5 - 300	-20 - 150	7.2	0.283
U8450020	D798-?SM	7.5	Microdot	Straight	0.71 - 100	0.028 - 4	-5 - 300	-20 - 150	7.2	0.283
U8450019	D798-?LF	7.5	Potted	Right Angle	0.71 - 100	0.028 - 4	-5 - 300	-20 - 150	8.9	0.35
U8454013	D7226	7.5	Potted	Right Angle	0.71 - 100	0.028 - 4	-5 - 300	-20 - 150	8.9	0.35
U8450012	D792	10	Potted	Straight	0.5 - 25	0.020 - 1	32 - 122	0 - 50	7.2	0.283
U8450013	D793	10	Potted	Right Angle	0.5 - 25	0.020 - 1	32 - 122	0 - 50	7.2	0.283

Other Thickness Gage Transducers

For use with 38DL PLUS and 45MG.

* Oxide Software only available for 38DL PLUS.

**E110-SP not available for 45MG.

†Adaptor required for E110 (part number 1/2XA/E110).

Transducer Part #	Part Number	Freq.	Tip Diameter		Transducer Type	Connector		Range in Steel		Temp. Range
		MHz	in.	mm		Type	Location	in.	mm	°F	°C
V260-SM	U8411019	15	0.080	2	Sonopen®	Microdot®	Straight	0.02 - 0.400	0.5 - 10	32 to 122	0 to 50
V260-RM	U8411018	15	0.080	2	Sonopen	Microdot	Right Angle	0.02 - 0.400	0.5 - 10	32 to 122	0 to 50
V260-45	U8411017	15	0.080	2	Sonopen	Microdot	45? Handle	0.02 - 0.400	0.5 - 10	32 to 122	0 to 50
M2017*	U8415002	20	0.250	6.35	Internal Oxide Scale	Microdot	Right Angle	Steel: 0.020 - 0.50 Oxide: 0.010 - 0.050	Steel: 0.5 - 12 Oxide: 0.25 - 1.25	32 to 122	0 to 50
M2091*	U8415018	20	0.250	6.35	Replaceable Delay Line Shear Wave	Microdot	Right Angle	Steel: 0.020 - 0.50 Oxide: 0.006 - 0.050	Steel: 0.5 - 12 Oxide: 0.150 - 1.25	32 to 122	0 to 50
E110-SB†**	U8471001	-	1.25	28.5	EMAT	BNC	Straight	0.080 - 5	2.0 - 125	32 to 176	0 to 80

Gage Dual Cables

Cable Part Number	Part Code	For Use With	Length		Cable Type	Plug Type
			feet	meters
LCMD-316-5B	U8800353	D790-SM	5.0	1.5	Standard	Straight
RLCMD-316-5B	U8800367	D790-SM	5.0	1.5	Standard	Rt Angle
LCMD-178-5B SSA	U8800352	D790-SM	5.0	1.5	Armored	Straight
RLCMD-178-5B SSA	U8800366	D790-SM	5.0	1.5	Armored	Rt Angle
LCLD-316-5G	U8800330	D790-RL	5.0	1.5	Standard	Straight
LCLD-316-5H	U8800331	D790-SL	5.0	1.5	Standard	Straight
LCMD-316-5C	U8800354	D791-RM	5.0	1.5	Standard	Straight
LCMD-316-5D	U8800355	D797-SM	5.0	1.5	Standard	Straight
LCMD-316-5J	U8800357	D798-SM	5.0	1.5	Standard	Straight
LCMD-316-5L	U8800358	D7906-SM	5.0	1.5	Standard	Straight
LCLPD-78-5	U8800332	MTD705	5.0	1.5	Standard	Straight
LCM-74-4	U8800348	V260-SM, V260-RM, V260-45, M2017	4.0	1.2	Standard	-
LCM-188-4 SSA	U8800342	V260-SM, V260-RM, V260-45, M2017	4.0	1.2	Armored	-
LCB-74-4	U8800320	E110-SB	4.0	1.2	Standard	-

The Panametrics-NDT Microscan transducers are frequently used with the Series 25 and Series 35 thickness gages, as well as other commercially available thickness gages, flaw detectors and ultrasonic instrumentation.

Microscan transducer part numbers reflect the connector designation:
RM = Right Angle Microdot®
SM = Straight Microdot
RB = Right Angle BNC
SB = Straight BNC
SU = Straight UHF

When selecting a transducer, please review the chart below or consult the Transducer Frequency Range in the Instruction Manual that was shipped with your gage.

Thickness Gage Model

Transducer Frequency Range

45MG
38DL PLUS

2.0 to 30 MHz

Contact Transducers

One of the advantages of a Panametrics-NDT Microscan contact transducer is its versatility; a single transducer can cover a broad thickness range in many engineering materials. Contact transducers are constructed with the unique WC-5 wearplate for greater durability and a longer life.

Frequency (MHz)	Element inches	Diameter mm	Transducer Part Number	Transducer Part Code
0.5	1	25	M101-SB	U8400017
1	1	25	M102-SB	U8400018
1	0.5	13	M103-SB	U8400020
2.25	0.5	13	M106-RM, M106-SM	U8400023, U8400025
2.25	0.5	13	M1036†	U8400019
5	0.5	13	M109-RM, M109-SM	U8400027, U8400028
5	0.25	6	M110-RM, M110-SM, M110H-RM**	U8400030, U8400031, U8400029
10	0.25	6	M112-RM, M112-SM, M112H-RM**	U8400034, U8400035, U8400033
10	0.125	3	M1016	U8400015
20	0.125	3	M116-RM, M116-SM	U8400038, U8400039
20	0.125	3	M116H-RM*	U8400037

RM = Right Angle Microdot; SM = Straight Microdot; SB = Straight BNC
†High Penetration Transducer *Use with Holder, P/N 2133 **Use with Holder, P/N 2132

SONOPEN® Transducers

The Sonopen® transducer has a replaceable delay line that is tapered to a small contact area. This transducer makes reliable thickness measurements in applications such as turbine blades, threads on plastic bottle necks and tight radii on plastic containers. High-temperature Sonopen delay lines are also available.

Frequency	Nominal Element Size		Transducer Part Numbers
MHz	inches	mm	Straight Handle	Right Angle Handle	45° Handle
15	0.125	3	V260-SM U8411019	V260-RM U8411018	V260-45 U8411017

Tip diameter
inches	mm	Part Number
0.08	2	DLP-3
0.06	1.5	DLP-302
0.08	2	DLP-301*

*High temperature delay for use up to 350° F (175° C)

Delay Line Transducers

Panametrics-NDT Microscan delay line transducers provide excellent performance on very thin materials, elevated temperatures or in applications that require a high degree of thickness resolution.

Frequency (MHz)	Element inches	Diameter mm	Transducer Part Number	Transducer Part Code	Holders
0.5	1	25	M2008	U8415001	-
2.25	0.5	13	M207-RB	U8410017	-
5	0.5	13	M206-RB	U8410016	-
5	0.25	6	M201-RM	U8410001	-
5	0.25	6	M201H-RM	U8411030	2127
10	0.25	6	M202-RM, M202-SM	U8410003, U8410004	-
10	0.25	6	M202H-RM	U8507023	2127
10	0.125	3	M203-RM, M203-SM	U8410006, U8410007	-
20	0.125	3	M208-RM, M208-SM	U8410019, U8410020	-
20	0.125	3	M208H-RM	U8410018	2133
20	0.125	3	M2055*	U8415013	-
30	0.25	6	V213-BC-RM*	U8411022	-

Replaceable Delay Lines

Standard Delay Lines

Standard delay lines are used in many applications. Special conditions such as high surface temperature, curvature of the material or hard-to-access areas may require the use of special delay lines.

Element Diameter		Delay Line Part Number	Maximum Thickness Measurement Limit*
Element Diameter			Steel Mode 2		Steel Mode 3		Plastic Mode 2
inches	mm		inches	mm	inches	mm	inches	mm
0.5	13	DLH-2	1.0	25	0.5	13	0.5	13
0.25	6	DLH-1	1.0	25	0.5	13	0.5	13
0.125	3	DLH-3	0.5	13	0.2	5	0.2	5

*Exact range depends on material sound velocity, transducer frequency, part geometry and surface condition.

High Temperature Delay Lines

High temperature delay lines function as a protective buffer between the hot surface of the test piece and the transducer's crystal. At elevated temperatures, intermittent contact is recommended to protect the transducer from thermal damage.

Element Diameter		High Temperature Delays
Element Diameter		To 350 °F (175 °C)	To 500 °F (260 °C)	To 900 °F (480 °C)
inches	mm	To 350 °F (175 °C)	To 500 °F (260 °C)	To 900 °F (480 °C)
0.5	13	DLHT-201	DLHT-2	DLHT-2G
0.25	6	DLHT-101	DLHT-1	DLHT-1G
0.125	3	DLHT-301	DLHT-3	DLHT-3G

Immersion Transducers

Panametrics-NDT Microscan immersion transducers are designed to transmit and receive ultrasound in water. Thickness measurements by immersion technique are often preferred when the test piece has a complex geometry or in online applications. Typical offline applications include wall thickness measurements on small diameter plastic or metal tubing, scanned or rotary measurements and thickness measurements on sharply curved parts. Transducer focusing may be necessary depending on the application.

Frequency	Element Diameter		Transducer Part Number	Transducer Part Code
(MHz)	inches	mm	Transducer Part Number	Transducer Part Code
2.25	0.5	13	M306-SU	U8410027
5	0.5	13	M309-SU	U8420001
5	0.25	6	M310-SU	U8420004
10	0.25	6	M312-SU	U8420008
15	0.25	6	M313-SU	U8420009
20	0.125	3	M316-SU	U8420011

Bubblers

We offer bubblers for easy implementation of immersion testing. They act as a holder for the transducers to maintain consistent water flow from transducer to test surface, and prevent the accumulation of air bubbles on the transducer face.

Part Number	Opening		Water Path		Fits Transducer Part Number
Part Number	inches	mm	inches	mm	Fits Transducer Part Number
B100	0.125	3	1.25	32	M310A-SM, M312A-SM, M316A-SM
B103*	0.35	9	0.575	14.5	M310-SU, M312-SU, M313-SU, M316-SU
B103W*	0.55	14	0.775	19.7	M306-SU, M309-SU
B103A*	0.35	9	0.575	14.5	same as B103
* The B103 has a V-notch shaped opening; the B103A and B103W are flat.

Bubbler Transducer Assembly

Handheld bubbler transducers are available in either 20 MHz (V316B) or 10 MHz (V312B). They are immersion transducers that screw onto a bubbler assembly (B120), which has a replaceable stainless steel tip and a water feed tube. They offer high resolution and easy access inspection of thin materials.

RBS-1 Immersion Tank

Panametrics-NDT RBS-1 immersion tank is designed to simplify ultrasonic thickness measurements using immersion techniques. It consists of a clear acrylic tank, a submersible pump and a transducer fixture in a single, portable unit. It is ideal for offline thickness measurements on metal, glass and plastic products such as small containers, pipe or tubing, sheets or plates or machined parts.

Tank
• 5.5 x 12 x 8 in (140 x 305 x 200 mm)
• 0.83 gallon (3.1 liter) capacity

Pump
• 0 to 0.25 gallons (0 to 0.9 liters) per minute
• 115 or 230 V, 30 Watt (voltage range 90 to 135 VAC), 50 to 60 Hz
• Submersible (ground fault interrupter circuit recommended)

Couplants

The use of couplant is almost always necessary to provide acoustic coupling between the transducer and the test piece. We offer various types of couplants to suit virtually all applications.

Part Number	Description	Volume	Application
A2 AP AQ AG	Propylene Glycol Propylene Glycol Propylene Glycol Propylene Glycol	2 oz (0.06 liter) 1 pint (0.47 liter) 1 quart (0.95 liter) 1 gallon (3.78 liter)	General purpose couplant for smooth surfaces. Chemically non-reactive; does not evaporate quickly. The maximum recommended temperature is 200 °F (90 °C)
B2 BQ	Glycerin Glycerin	2 oz. (0.06 liter) 1 qt. (0.95 liter)	General purpose, more viscous and has a high acoustic impedance making it the preferred couplant for rough surfaces and highly attenuating materials.
D12 DG D-5G	Gel Type Gel Type Gel Type	12 oz. (0.35 liter) 1 gal. (3.78 liter) 5 gal. (18.90 liter)	Rough surfaces such as sand-cast metals and fiberglass layups, weld inspections, overhead surfaces or vertical walls.
E-2	Ultratherm	2 oz. (0.06 liter)	500 °F to 970 °F (260 °C to 520 °C)
G-2	Medium Temp	2 oz. (0.06 liter)	0 °F to 600 °F (-12 °C to 315 °C) Easy removal at high temperatures. Non-toxic and biodegradable
SWC	Shear Wave	4 oz. (0.12 liter)	Normal Incidence Shear Wave, non-toxic, water soluble organic substance of very high viscosity.

Calibration Test Blocks

Test blocks are necessary for the calibration of ultrasonic thickness gages and should be used to maintain and verify the accuracy, dependability and reliability of ultrasonic measurements. Blocks are held to tighter tolerances than called out in ASTM E797 code. Metric test blocks are available.

Part Number	Material	Steps
2211E	304 Stainless Steel	.100, .200, .300, .400 and .500 in
2212E	1018 Carbon Steel	.250, .500, .750, .400 and 1.00 in
2213E	7075-T6 Aluminum	.100, .200, .300, .400 and .500 in
2214E	1018 Carbon Steel	.100, .200, .300, .400 and .500 in
2214M	1018 Carbon Steel	2.5, 5.0, 7.5, 10.0 and 12.5 mm

?Transducer Cables
Olympus-NDT offers a wide selection of transducer cables suitable for all ultrasonic thickness gaging instrumentation.

Part Number	Connectors	Available Lengths
LCM-74-X	Small LEMO® 00 to Microdot®	3 ft (0.9 m), 4 ft (1.2 m), 6 ft (1.8 m)
LCB-74-X	Small LEMO® 00 to BNC	3 ft (0.9 m), 4 ft (1.2 m), 6 ft (1.8 m)
BCM-74-X	BNC to Microdot®	3 ft (0.9 m), 4 ft (1.2 m), 6 ft (1.8 m)
LCU-74-X	LEMO® 00 to UHF	3 ft (0.9 m)

Standard

• Standard cables are recommended for normal usage.

Heavy Duty - Teflon®

• Heavy duty, Teflon® (HD) transducer cables may provide durability and longer life.

Waterproof

• Waterproof (W) cables are recommended in many tests with immersion transducers. These cables provide a waterproof connection good to about 30 ft (10 m) of fresh water. At greater depths, special cables are available.

Heavy Duty - Armored PVC Jacket

• Heavy duty, armored PVC jacket (HDAP) transducer cables have a spiral stainless steel jacket with a solid PVC coating. Maximum length is 20 ft (7 m).

Heavy Duty - Armored Silicone Jacket

• Heavy duty, armored super flexible silicone jacket (HDAS) transducer cables combine a spiral stainless steel jacket with a heavy silicone coating for great flexibility. Length can be specified up to 20 ft (7 m).

Heavy Duty - Stainless Steel

• Heavy duty, armored stainless steel jacket (SSA) transducer cables are recommended for heavy and industrial use provide flexibility, protection and long life.

深圳華清儀器儀表有限公司