重量（凈重)	88.5kg

SQP42-50-21-21AD-18 TOKIMEC 東京計器 TOKYO KEIKI 雙聯定量葉片油泵SQP42-50-21-21AD_18

雙聯定量葉片油泵SQP42-50-21-21AD_18

型號規格

1 適用的液壓油

無記號：石油類液壓油

Ｆ３：磷酸酯類液壓油

Ｆ１１：水?乙二醇類液壓油

2 低噪音?定量雙聯葉片泵

SQP(S)21 系列

SQP(S)31，32 系列

SQP(S)41，42，43 系列

3 聯（軸側）液壓泵排量記號

系列	排量記號
SQP(S)2*	10, 12, 14, 15, 17, 19, 21
SQP(S)3*	17, 21, 25, 30, 32, 35, 38
SQP(S)4*	30, 35, 38, 42, 50, 60

4 第二聯（泵蓋側）液壓泵排量記號

系列	排量記號
SQP(S)*1	2, 3, 4, 5, 6, 7, 8, 9, 11, 12, 14
SQP(S)*2	10, 12, 14, 15, 17, 19, 21
SQP(S)*3	17, 21, 25, 30, 32, 35, 38

5 軸端形狀

86：方鍵平行軸

6 聯（軸側）泵排油口位置（由泵蓋側看）

A: 吸油口的相反側

B: 由吸油口逆時針旋轉 90°

C: 與吸油口在同一線上

D: 由吸油口順時針旋轉 90°

7 第二聯（泵蓋側）泵排油口位置（由泵蓋側看）

A: 由吸油口逆時針旋轉 135°（吸油口的相反側）

B: 由吸油口逆時針旋轉 45°（90°）

C: 由吸油口順時針旋轉 45°（與吸油口在同一線上）

D: 由吸油口順時針旋轉 135°（90°）

（注）?（　）內角度是ＳＱＰ（Ｓ）43 系列。

8 液壓泵安裝方式

無記號：法蘭安裝型

2 ＊：腳架安裝型

腳架安裝面與聯泵排油口相對位置（參考下圖）

腳架安裝記號	以腳架安裝面為基準由軸側看到的聯泵排口的位置
2	上（12點方向）
23	右（3點方向）
26	下（6點方向）
29	左（9點方向）

9 旋轉方向（由軸側看）

無記號：右旋轉（順時針）

LH：左旋轉（逆時針）

10 設計編號：18

SQP42-50-21-21AD-18 TOKIMEC 東京計器 TOKYO KEIKI 雙聯定量葉片油泵SQP42-50-21-21AD_18

東京計器油泵TOKYOKEIKI葉片泵特點：

1，本系列是專為低噪音工況而開發的高壓性能子母葉片泵。

2，使用于注塑機械、橡膠機械、壓鑄機械、機床等各種液壓系統中。

3，增加了脈動衰減結構的設計，極大降低了壓力的脈動，使噪音更低，音原則質更流暢。

4，使用加厚的外殼設計，增加了泵的強度和抗震性，同時消音性能更*。

東京機器油泵適用范圍：本產品主要用于船舶，注塑機械，橡膠機械，油壓機械，壓鑄機械，塑料機械，打包機械，工程機械，機床機械，礦山機械，熱壓機械，制鞋機械，陶瓷機械，制磚機械，發泡機械，鍛造機械，流化機械，拉伸機械，等機械液壓配件。

東京計器葉片泵的安裝，

1油泵的支架座結構要牢固，剛性好，并能充分吸收振動，

2油泵可安裝成任何方向，泵和電機軸必須對正，同軸度應控制在0.1mm以?xún)?nèi)，

3，吸入阻力不應太高，以防產生空蝕現象。

4，注意進油口處連接法蘭，接頭以及整個吸油管道必須密封，防止漏氣。

SQP42-50-21-21AD-18 TOKIMEC 東京計器 TOKYO KEIKI 雙聯定量葉片油泵SQP42-50-21-21AD_18

SQP42-50-21-21AD-18 TOKIMEC / TOKYO KEIKI Double Fixed Displacement Vane Pump

Model Specification Description

1. Applicable Hydraulic Oil

No marking: Petroleum-based hydraulic oil

F3: Phosphate ester hydraulic fluid

F11: Water-glycol hydraulic fluid

2. Low-Noise Fixed Displacement Double Vane Pump Series

SQP(S)21 Series

SQP(S)31, 32 Series

SQP(S)41, 42, 43 Series

3. Displacement Code for Front Pump (Shaft Side)

Series	Displacement Codes
SQP(S)2*	10, 12, 14, 15, 17, 19, 21
SQP(S)3*	17, 21, 25, 30, 32, 35, 38
SQP(S)4*	30, 35, 38, 42, 50, 60

4. Displacement Code for Rear Pump (Cover Side)

Series	Displacement Codes
SQP(S)*1	2, 3, 4, 5, 6, 7, 8, 9, 11, 12, 14
SQP(S)*2	10, 12, 14, 15, 17, 19, 21
SQP(S)*3	17, 21, 25, 30, 32, 35, 38

5. Shaft End Configuration

86: Parallel shaft with square key

6. Outlet Port Position of Front Pump (Viewed from Pump Cover Side)

A: Opposite to suction port

B: 90° counterclockwise from suction port

C: In-line with suction port

D: 90° clockwise from suction port

7. Outlet Port Position of Rear Pump (Viewed from Pump Cover Side)

A: 135° counterclockwise from suction port (opposite side of suction port)

B: 45° counterclockwise from suction port (90° for SQP(S)43 series, see bracket note)

C: 45° clockwise from suction port (in-line with suction port for SQP(S)43 series, see bracket note)

D: 135° clockwise from suction port (90° for SQP(S)43 series, see bracket note)

Note: Angles in parentheses apply exclusively to SQP(S)43 series.

8. Pump Mounting Form

No marking: Flange mounted type

Prefix 2: Foot-mounted type

Relative position of pump outlet vs foot mounting face (viewed from shaft end):

Foot Mount Code	Outlet Direction
2	Top (12 o’clock position)
23	Right (3 o’clock position)
26	Bottom (6 o’clock position)
29	Left (9 o’clock position)

9. Rotation Direction (Viewed from Shaft End)

No marking: Clockwise (Right-hand rotation)

LH: Counterclockwise (Left-hand rotation)

10. Design Code: 18

Features of TOKYO KEIKI / TOKIMEC Vane Pump

This high-pressure intra-vane pump range is specially developed for low-noise operating conditions.
Widely applied in hydraulic systems for injection molding machines, rubber processing equipment, die-casting machines and machine tools.
Built-in pressure pulsation damping structure drastically reduces flow pulsation, lowering operating noise and enabling smoother hydraulic performance.
Reinforced thick pump housing improves structural strength, shock resistance and noise attenuation performance.

Application Scope

Suitable as hydraulic component for ship machinery, injection molding machinery, rubber machinery, general hydraulic equipment, die-casting machines, plastic machinery, baling equipment, construction machinery, machine tools, mining equipment, hot-press machinery, shoe-making machinery, ceramic & brick forming machines, foaming equipment, forging machinery, fluidization equipment and metal stretching machinery.

Pump Installation Requirements

The pump support bracket shall be rigid and robust to effectively absorb operational vibration.
The pump can be mounted at any orientation; concentricity between pump shaft and motor shaft must be controlled within 0.1 mm.
Limit excessive suction resistance to avoid pump cavitation.
Ensure full sealing of suction flange, pipe fittings and entire suction pipeline to prevent air ingress.

Model: SQP42-50-21-21AD-18 TOKIMEC / TOKYO KEIKI Double Fixed Displacement Vane Pump

雙聯定量葉片油泵SQP42-50-21-21AD_18 返回列表頁

SQP42-50-21-21AD-18 TOKIMEC / TOKYO KEIKI Double Fixed Displacement Vane Pump