HN500一體化振動變送器，將振動傳感器、精密測量電路集成在一起,實現了傳統的“傳感器十變送器"模式的振動測量系統的功能,實現了經濟型高精度振動測量系統,該變送器可直接連接DCS、PLC或其它系統,是風機、水泵等工廠設備振動測量的理想選擇。

HN500一體化振動變送器 技術參數：

2．1 頻率響應：10 ～ 1000 Hz  *  或者5-1000 Hz（特殊說明）

2．2 自振頻率：10Hz

2．3 測量范圍：0-20mm/s

2．4 輸出電流：4～20mA  

2．5輸出阻抗：≤500Ω

2．6工作電壓：DC12-36V

2. 7接線方式：二線制

2．7最大加速度：10g

2．8測量方向：通用（垂直或水平）

2．9 使用環境：溫   度  -40℃～+85℃   相對濕度 ≤90%

2．10 外形尺寸：φ33mm×76mm 

2．11 安裝：M10*1.5或其他規格

2．12 重    量： 約350g

3. 13 外殼材質：304不銹鋼

3．安  裝 

3．1 安裝位置：垂直或者水平安裝于被測振動點上，將傳感器固定在被測殼體上，然后將傳器擰在上面吸附即可。

3．2 安裝尺寸及規范：參看圖一，若變送器安裝位置受到高溫蒸汽等沖刷時，為降低變送器環境溫度、需加防護措施，一般情況下可不加防護。

3．3 接線說明：棕色導線接DC24V電源正端，藍色導線接4-20mA輸出，。連接導線要求有良好的絕緣性能，采用二芯屏蔽電纜。

The HN500 integrated vibration transmitter integrates the vibration sensor and the precise measurement circuit, achieving the functions of the traditional "sensor + transmitter" mode vibration measurement system. It realizes an economical and high-precision vibration measurement system. This transmitter can be directly connected to DCS, PLC or other systems, making it an ideal choice for vibration measurement of factory equipment such as fans and pumps.

HN500 Integrated Vibration Transmitter Technical Specifications:

2.1 Frequency Response: 10 - 1000 Hz  *  or 5 - 1000 Hz (if specified) 

2.2 Natural Frequency: 10 Hz 

2.3 Measurement Range: 0 - 20 mm/s 

2.4 Output Current: 4 - 20mA 

2.5 Output Impedance: ≤ 500Ω 

2.6 Operating Voltage: DC 12 - 36V 

2. 7-wire connection method: Two-wire system 

2.7 Maximum acceleration: 10g 

2.8 Measurement Direction: General (Vertical or Horizontal) 

2.9 Operating Environment: Temperature -40℃ to +85℃; Relative Humidity ≤ 90% 

2.10 Dimensions: φ33mm × 76mm 

2.11 Installation: M10*1.5 or other specifications 

2.12 Weight: Approximately 350g 

3. 13 Shell material: 304 stainless steel

3. Installation 

3.1 Installation Position: Install vertically or horizontally on the vibration measurement point. Fix the sensor onto the measured shell, and then screw the transducer onto it to attach it. 

3.2 Installation Dimensions and Specifications: Refer to Figure 1. If the installation position of the transmitter is exposed to high-temperature steam or other corrosive substances, in order to reduce the ambient temperature of the transmitter, protective measures should be taken. Generally, no protection is required. 

3.3 Wiring Instructions: The brown wire is connected to the positive terminal of the DC24V power supply, and the blue wire is connected to the 4-20mA output. The connecting wires must have good insulation performance and should be connected using a two-core shielded cable.